DI3201 DI3201-A-V001

DI3201 DI3201-A-V001的工作方式為掃描加中斷，這既可保證它能有序地工作，避免繼電控制系統常出現的"冒險競爭"，其控制結果總是確定的；而且又能應急處理急于處理的控制，保證了DI3201 DI3201-A-V001對應急情況的及時響應，使PLC能可靠地工作。

為監控PLC運行程序是否正常，DI3201 DI3201-A-V001系統都設置了"看門狗"（Watchingdog）監控程序。運行用戶程序開始時，先清"看門狗"定時器，并開始計時。當用戶程序一個循環運行完了，則查看定時器的計時值。若超時（一般不超過100ms），則報警。嚴重超時，還可使PLC停止工作。用戶可依報警信號采取相應的應急措施。定時器的計時值若不超時，則重復起始的過程，DI3201 DI3201-A-V001將正常工作。顯然，有了這個"看門狗"監控程序，可保證DI3201 DI3201-A-V001用戶程序的正常運行，可避免出現"死循環"而影響其工作的可靠性。

DI3201 DI3201-A-V001還有很多防止及檢測故障的指令，以產生各重要模塊工作正常與否的提示信號?？赏ㄟ^(guò)編制相應的用戶程序，對DI3201 DI3201-A-V001的工作狀況，以及PLC所控制的系統進行監控，以確保其可靠工作。DI3201 DI3201-A-V001每次上電后，還都要運行自檢程序及對系統進行初始化。這是系統程序配置了的，用戶可不干預。出現故障時有相應的出錯信號提示。

The working mode of DI3201 DI3201-A-V001 is scanning and interruption, which can ensure that it can work orderly and avoid the "risk competition" often occurred in relay control system, and its control result is always determined; Moreover, it can control the emergency treatment, ensure the timely response of PLC to the emergency situation, and make the PLC work reliably.

In order to monitor whether the PLC operation program is normal, The DI3201 DI3201-A-V001 system is equipped with a "watchdog" monitoring program. When running the user program, first b the "watchdog" timer and start timing. When the user program runs a cycle, check the timing value of the timer. If it times out (generally no more than 100ms), it will give an alarm. Serious timeout can also stop the DI3201 DI3201-A-V001. The user can take corresponding emergency measures according to the alarm signal. If the timer does not time out, repeat the starting process and the PLC will work normally. Obviously, with this "watchdog" monitoring program, the normal operation of the PLC user program can be guaranteed and the "dead cycle" can be avoided And affect the reliability of its work.