產品詳情
進口氣動隔膜閥
深圳派克閥門有限公司總代理：德國雷普LIP氣動隔膜閥
進口LIPGTRBN氣動隔膜閥常閉式氣動襯氟隔膜閥的開啟是由壓縮空氣推動薄膜耐壓縮彈簧，使閥桿作軸向運動帶動閥瓣升高而達到開啟，當中斷氣源時，由于彈簧的預緊力作用而使閥門處于常閉的位置。閥門配有手操作部件，當氣源發生故障而中斷時，且閥門急需開啟的緊急狀況時，可逆時針旋轉手輪使閥門開啟。
LIPGTRBNnormally closed pneumatic lined diaphragm opening is driven by compressed air film resistance to compression of the spring, so that axial movement of the stem valve driven by increased achieve open, which expire source, due to the b of the spring preload leaving the valve is in a normally closed b. When equipped with a hand operated valve parts, when the air supply is interrupted when a fault occurs, and valves needed to open an emergency situation, you can make the counter-clockwise rotation of the hand wheel valve open.
主要技術參數The main technical beters：
壓力等級：1.0MPA 適用溫度：≤100℃
氣源壓力要求：0.7MPA 適用介質：酸堿等腐蝕性介質
閥體材料：不銹鋼316L 閥蓋：不銹鋼316L
襯里；PTFE 隔膜：PTFE
氣缸：球墨鑄鐵 活塞：碳鋼
閥桿：碳鋼 手輪：瑪鋼
Pressure Rating: 1.0MPA Temperature: ≤100 ℃
Air pressure requirements: 0.7MPA Medium: acid and other corrosive media
Body material: stainless steel 316L valve cover: Stainless steel 316L
Lining; PTFE Diaphragm: PTFE
Cylinder: Ductile iron piston: Carbon
Stem: Carbon steel handwheel: Malleable
可能發生故障的方法及處理方法
The b may be faulty and treatment
可能發生的故障
Failure may occur 原因The reason 消除方法Remedy
手輪轉運不靈活 閥桿上積有污垢或螺紋損傷
Plot there is dirt or damage to the valve stem threads 清除污垢或修整并注以潤滑劑Remove dirt or trimming and injection with a lubricant
閥桿螺母磨損或拉裂 Stem nut wear or crack 更換閥桿螺母
Replace the stem nut
閥桿彎曲 Stem bending 校正或更換閥桿
Correction or replacement of the valve stem
閥體與閥蓋連接處滲漏Body and bonnet junction leakage 連接螺栓緊固不均勻Connecting bolt uneven 均勻緊固Evenly tighten
密封面間滲漏 密封面間積有污垢 消除污垢并不得損傷密封面
彈簧預緊力過小 適當調節預緊力
密封面輕微損傷 應按原曲面修整
隔膜擰得過緊或過松 適當調節隔膜松緊程度
隔膜嚴重被蝕或損裂 更換隔膜
供氣時閥門不能自動開啟 輸入氣源壓力過低 補充氣源壓力
彈簧預緊力過大 適當調節預緊力
產地：德國
產品品牌：德國雷普（LIP）
深圳派克閥門有限公司總代理：德國雷普LIP氣動隔膜閥
進口LIPGTRBN氣動隔膜閥常閉式氣動襯氟隔膜閥的開啟是由壓縮空氣推動薄膜耐壓縮彈簧，使閥桿作軸向運動帶動閥瓣升高而達到開啟，當中斷氣源時，由于彈簧的預緊力作用而使閥門處于常閉的位置。閥門配有手操作部件，當氣源發生故障而中斷時，且閥門急需開啟的緊急狀況時，可逆時針旋轉手輪使閥門開啟。
LIPGTRBNnormally closed pneumatic lined diaphragm opening is driven by compressed air film resistance to compression of the spring, so that axial movement of the stem valve driven by increased achieve open, which expire source, due to the b of the spring preload leaving the valve is in a normally closed b. When equipped with a hand operated valve parts, when the air supply is interrupted when a fault occurs, and valves needed to open an emergency situation, you can make the counter-clockwise rotation of the hand wheel valve open.
主要技術參數The main technical beters：
壓力等級：1.0MPA 適用溫度：≤100℃
氣源壓力要求：0.7MPA 適用介質：酸堿等腐蝕性介質
閥體材料：不銹鋼316L 閥蓋：不銹鋼316L
襯里；PTFE 隔膜：PTFE
氣缸：球墨鑄鐵 活塞：碳鋼
閥桿：碳鋼 手輪：瑪鋼
Pressure Rating: 1.0MPA Temperature: ≤100 ℃
Air pressure requirements: 0.7MPA Medium: acid and other corrosive media
Body material: stainless steel 316L valve cover: Stainless steel 316L
Lining; PTFE Diaphragm: PTFE
Cylinder: Ductile iron piston: Carbon
Stem: Carbon steel handwheel: Malleable
可能發生故障的方法及處理方法
The b may be faulty and treatment
可能發生的故障
Failure may occur 原因The reason 消除方法Remedy
手輪轉運不靈活 閥桿上積有污垢或螺紋損傷
Plot there is dirt or damage to the valve stem threads 清除污垢或修整并注以潤滑劑Remove dirt or trimming and injection with a lubricant
閥桿螺母磨損或拉裂 Stem nut wear or crack 更換閥桿螺母
Replace the stem nut
閥桿彎曲 Stem bending 校正或更換閥桿
Correction or replacement of the valve stem
閥體與閥蓋連接處滲漏Body and bonnet junction leakage 連接螺栓緊固不均勻Connecting bolt uneven 均勻緊固Evenly tighten
密封面間滲漏 密封面間積有污垢 消除污垢并不得損傷密封面
彈簧預緊力過小 適當調節預緊力
密封面輕微損傷 應按原曲面修整
隔膜擰得過緊或過松 適當調節隔膜松緊程度
隔膜嚴重被蝕或損裂 更換隔膜
供氣時閥門不能自動開啟 輸入氣源壓力過低 補充氣源壓力
彈簧預緊力過大 適當調節預緊力
產地：德國
產品品牌：德國雷普（LIP）
