產(chǎn)品詳情
1. Low Temperature Soldering:?
High Power / mass ration tips and integrated?
heater / thermocouple delivers the best thermal?
recovery in the market along with lower soldering?
temperatures.
2. Read & Feed:
We use one wire buried deep in the tip of the?
copper to “read & feed.” Our thermocouple?
and heating element are one in the same and?
are microprocessor driven over a sensor at 60?
hertz (60x a second) utilizing up to 140 watt?
transber. This is why our thermal perbance?
cannot be matched.
3. Initial Heat Up:
A conventional station takes between 10 to 90?
seconds to reach 360° C. Any JBC station with?
a T210 hand piece reaches this temperature in?
only two seconds.
4. Outstanding Tip Life:
Lasting up to five times longer as soon as?
the soldering iron is left in the stand, the tip?
temperature automatically drops to 200° C,?
decreasing oxidation and wear. Resulting in a?
working life three to five times longer than that?
of the conventional tip. When the soldering iron?
is taken out of the stand again, the working?
temperature is instantaneously reached.?
NOTE: It varies by tip geometry, temperature?
settings, solder, flux, and the person using it;?
However generally, it ranges between 25,000?
and 100,000 solder joints.
5. Quick Change Over Tips:
No tools needed to change the tip. Just place in?
holder, pull and insert the new tip. Reduces your?
idle time while increasing operator safety.
6. Ergonomic Design:
The JBC soldering iron are currently the lightest,?
smallest and most ergonomic hand piece?
available. Offering the shortest tip to hand?
distance and a higher working perbance.
7. Process Control:
Regain control of your process! Set temperatures?
limits, read counters, block the station with PIN?
or block the keypad.
8. Inbligent Heat Management:
Extend tip life by reducing temperature and?
reduce energy usage to 10 watts during sleep?
and 4 watts when hibernating.
9. Easy Calibration:
Since JBC technology is microprocessor driven,?
it not necessary to recalibrate any of the JBC?
stations but, if required, calibration of the?
soldering tip can easily be done by using TI 2800?
Thermometer and the temperature adjustment?
featured in the station’s menu.
10. Improved Productivity:
The JBC technology gives an 80% improvement?
over the perbance of the best soldering?
station available in the market. In the following?
graphs, based on practical test, we show this?
superiority.
High Power / mass ration tips and integrated?
heater / thermocouple delivers the best thermal?
recovery in the market along with lower soldering?
temperatures.
2. Read & Feed:
We use one wire buried deep in the tip of the?
copper to “read & feed.” Our thermocouple?
and heating element are one in the same and?
are microprocessor driven over a sensor at 60?
hertz (60x a second) utilizing up to 140 watt?
transber. This is why our thermal perbance?
cannot be matched.
3. Initial Heat Up:
A conventional station takes between 10 to 90?
seconds to reach 360° C. Any JBC station with?
a T210 hand piece reaches this temperature in?
only two seconds.
4. Outstanding Tip Life:
Lasting up to five times longer as soon as?
the soldering iron is left in the stand, the tip?
temperature automatically drops to 200° C,?
decreasing oxidation and wear. Resulting in a?
working life three to five times longer than that?
of the conventional tip. When the soldering iron?
is taken out of the stand again, the working?
temperature is instantaneously reached.?
NOTE: It varies by tip geometry, temperature?
settings, solder, flux, and the person using it;?
However generally, it ranges between 25,000?
and 100,000 solder joints.
5. Quick Change Over Tips:
No tools needed to change the tip. Just place in?
holder, pull and insert the new tip. Reduces your?
idle time while increasing operator safety.
6. Ergonomic Design:
The JBC soldering iron are currently the lightest,?
smallest and most ergonomic hand piece?
available. Offering the shortest tip to hand?
distance and a higher working perbance.
7. Process Control:
Regain control of your process! Set temperatures?
limits, read counters, block the station with PIN?
or block the keypad.
8. Inbligent Heat Management:
Extend tip life by reducing temperature and?
reduce energy usage to 10 watts during sleep?
and 4 watts when hibernating.
9. Easy Calibration:
Since JBC technology is microprocessor driven,?
it not necessary to recalibrate any of the JBC?
stations but, if required, calibration of the?
soldering tip can easily be done by using TI 2800?
Thermometer and the temperature adjustment?
featured in the station’s menu.
10. Improved Productivity:
The JBC technology gives an 80% improvement?
over the perbance of the best soldering?
station available in the market. In the following?
graphs, based on practical test, we show this?
superiority.
